A Lumped-Element Circuit Model of Ferrite Chokes

Andrea Orlando; Marina Koledintseva; Daryl G. Beetner; Peng Shao; Phil Berger

doi:10.1109/ISEMC.2010.5711373

A Lumped-Element Circuit Model of Ferrite Chokes

Andrea Orlando
, Marina Koledintseva
, Daryl G. Beetner
, Peng Shao
, Phil Berger

Electrical and Computer Engineering

Research output: Contribution to journal › Article › peer-review

Abstract

An RLC model of ferrite chokes for suppressing common-mode (CM) currents is presented. The equivalent lumped-element circuit parameters are obtained from the frequency-dependent input impedance of a ferrite choke on a wire above the ground plane. This input impedance can be either measured (using vector network analyzer or impedance analyzer), or numerically modeled based on the known ferrite material properties (permittivity and permeability). An example of using both numerical modeling and measurements is provided. Results show good agreement at comparatively low frequencies (below 200 MHz). The upper frequency limit for the proposed equivalent lumped-circuit model is discussed.

Original language	American English
Journal	Proceedings of the 2010 IEEE International Symposium on Electromagnetic Compatibility (2010, Fort Lauderdale, FL)
DOIs	https://doi.org/10.1109/ISEMC.2010.5711373
State	Published - Jan 1 2010

Keywords

Electric Impedance
Electric Impedance Measurement
Electric Network Analysis
Electric Network Analyzers
Electromagnetic Compatibility
Electromagnetism
Ferrite

Disciplines

Electrical and Computer Engineering

Access to Document

10.1109/ISEMC.2010.5711373License: CC BY

https://doi.org/10.1109/ISEMC.2010.5711373

Cite this

@article{c2b31183fae94f34baaa0eb6c7d3fc1b,

title = "A Lumped-Element Circuit Model of Ferrite Chokes",

abstract = " An RLC model of ferrite chokes for suppressing common-mode (CM) currents is presented. The equivalent lumped-element circuit parameters are obtained from the frequency-dependent input impedance of a ferrite choke on a wire above the ground plane. This input impedance can be either measured (using vector network analyzer or impedance analyzer), or numerically modeled based on the known ferrite material properties (permittivity and permeability). An example of using both numerical modeling and measurements is provided. Results show good agreement at comparatively low frequencies (below 200 MHz). The upper frequency limit for the proposed equivalent lumped-circuit model is discussed.",

keywords = "Electric Impedance, Electric Impedance Measurement, Electric Network Analysis, Electric Network Analyzers, Electromagnetic Compatibility, Electromagnetism, Ferrite",

author = "Andrea Orlando and Marina Koledintseva and Beetner, \{Daryl G.\} and Peng Shao and Phil Berger",

year = "2010",

month = jan,

day = "1",

doi = "10.1109/ISEMC.2010.5711373",

language = "American English",

journal = "Proceedings of the 2010 IEEE International Symposium on Electromagnetic Compatibility (2010, Fort Lauderdale, FL)",

}

TY - JOUR

T1 - A Lumped-Element Circuit Model of Ferrite Chokes

AU - Orlando, Andrea

AU - Koledintseva, Marina

AU - Beetner, Daryl G.

AU - Shao, Peng

AU - Berger, Phil

PY - 2010/1/1

Y1 - 2010/1/1

N2 - An RLC model of ferrite chokes for suppressing common-mode (CM) currents is presented. The equivalent lumped-element circuit parameters are obtained from the frequency-dependent input impedance of a ferrite choke on a wire above the ground plane. This input impedance can be either measured (using vector network analyzer or impedance analyzer), or numerically modeled based on the known ferrite material properties (permittivity and permeability). An example of using both numerical modeling and measurements is provided. Results show good agreement at comparatively low frequencies (below 200 MHz). The upper frequency limit for the proposed equivalent lumped-circuit model is discussed.

AB - An RLC model of ferrite chokes for suppressing common-mode (CM) currents is presented. The equivalent lumped-element circuit parameters are obtained from the frequency-dependent input impedance of a ferrite choke on a wire above the ground plane. This input impedance can be either measured (using vector network analyzer or impedance analyzer), or numerically modeled based on the known ferrite material properties (permittivity and permeability). An example of using both numerical modeling and measurements is provided. Results show good agreement at comparatively low frequencies (below 200 MHz). The upper frequency limit for the proposed equivalent lumped-circuit model is discussed.

KW - Electric Impedance

KW - Electric Impedance Measurement

KW - Electric Network Analysis

KW - Electric Network Analyzers

KW - Electromagnetic Compatibility

KW - Electromagnetism

KW - Ferrite

UR - https://scholarsmine.mst.edu/ele_comeng_facwork/2396

UR - https://doi.org/10.1109/ISEMC.2010.5711373

U2 - 10.1109/ISEMC.2010.5711373

DO - 10.1109/ISEMC.2010.5711373

M3 - Article

JO - Proceedings of the 2010 IEEE International Symposium on Electromagnetic Compatibility (2010, Fort Lauderdale, FL)

JF - Proceedings of the 2010 IEEE International Symposium on Electromagnetic Compatibility (2010, Fort Lauderdale, FL)

ER -

A Lumped-Element Circuit Model of Ferrite Chokes

Abstract

Keywords

Disciplines

Access to Document

Other files and links

Fingerprint

Cite this